Shelbourne Stripper Header

[Click on the label "stripper head" at the bottom of post for more posts on the subject.] 

Wednesday, June 20, 2012, we took delivery of a new CVS 32' header.  There are no other units in our immediate area to draw information from about their use.  There are two 32', 2011 units at Worley, ID run by Seth Melhorn on relatively flat (or gentle slopping ground). Eric Thorn of Dayton, WA runs two 25' AgCo units on 40% slopes.  The Shelbourne website gives the basic combine setup information.  Ag Talk:  (go to links page) appears to have helpful information for trouble shooting.  This post will be updated as I find useful information relating to harvesting with the stripper header.

       

Lots of good info on the Shelbourne site, setup for a specific combine, Maintenance , settings , etc. http://www.shelbourne.com/harvesting/stripper-header Remember to change the gear box oil every year and use only Mobil 1 full synthetic 75 / 90. Run the header low enough so the stripping rotor can reach the lowest heads. Once you find the right header height, set the hood so the tip of the grain heads are about level with the top of the hood nose. This will bend the heads and tops of the stems forward far enough to present the "wall of straw" in front of the stripper rotor, so any seeds that fly forward are bounced back into the stripper rotor. Bending the crop forward like that also causes the crop to spring back into the rotor in a way that the heads will be stripped off and thrown over the rotor into the table auger instead of out the front of the header. ( see drawings under "design history" to better understand this) Lots of good info under "how to set up your combine." Stripper rotor speed, concave mods, etc.

---- I'm in agreement with everything Jon, Josh, and Phil have already said. To add a bit to Jon's discussion on selecting a head height, there are several reasons you don't want to go any lower than you have too, header loss can become an issue not only because the "wall" of wheat is missing but in varieties prone to shattering if you run the nose of the hood too low so that the heads are above it you actually force the wheat to do a double bend, it bends towards the combine when it first comes into contact then has to bend back around the nose of the hood, then rapidly snap back upright prior to hitting the rotor. I've seen the mechanics of this cause a great deal of shatter before the wheat ever gets to the rotor. ---- Most header loss comes from running excessive rotor speed and too slow of ground speed. Only run the rotor as fast as you need to, the head as low as you have too, then drive fast. When conditions are good the field should look almost a little shaggy behind. If you are removing the entire head then you are either running the rotor too fast, the head too low, or a combination of both. Is header loss a problem in drought damaged wheat that is thin and short? How about going through winter killed or drowned out patches? Also, how do they handle going through weedy patches, like kochia? You get little stripper header loss if you push the header as hard as possible. Have had good results in drought damaged stuff that yield as little as 15 bu /a. Very short wheat is a danger to the stripper rotor if your fields have rocks.  Weeds like kochia go through pretty good, upright weeds will often have part of the leaves stripped off with most of the plant still standing in the field, so less weeds go in the combine than direct cut stuff. RVS Rice Special Range: 2002 onwards (10 to 28 foot widths) RSD Range: 2004 onwards (10 to 32 foot widths) CVS Cereal special Range: 2001 onwards (10 to 32 foot widths) These three models share a common frame design. The auger and rotor are placed closer together and grain is moved directly from the rotor to the auger. The deeper flighted larger diameter auger is able to handle more straw than before, this coupled with a larger shear bolt gives both these machines a significant advantage when harvesting lodged crops. Both models feature a new variable speed belt drive which enables the operator to make rotor speed adjustments from the cab. The RVS range features more stainless steel than on previous rice special models. The crop deflector, top hood and floor are stainless and the auger flighting and retractable auger fingers are made from hardened steel. Extensive field testing has proven that a deeper flighted auger sitting in a trough will feed better than a smaller one sitting on a flat pan. It is with this theory in mind that the RX shaker pan machine was discontinued in favour of the direct feeding RVS header. The RVS and CVS machines both feature variable speed drive systems enabling the operator to adjust the rotor speed from the cab. The RSD model is equipped with a fixed pulley belt drive using 4 belts. This is recommended for rice and grass seed applications where few speed changes are necessary and more power is required at the rotor.

lodged wheat: My first experience with the shelbourne header was in lodged winter wheat and i had all of the problems listed in the previous replies and then some. i called a man in SD who had been using shelbournes for many years and he asked me how fast i was traveling. turns out i was going too slow. In lodged or perfectly flat wheat, set the head on the ground and do not allow your speed to dip below 3.2 mph and set the shield to the "lodged wheat setting." When i followed his advise, everything worked wonderful. haven't had a problem since. we have harvested 85 bu spring wheat laying flat, like 1" depth, and done an amazing job. just don't slow down unless you are turning. when going into lodged wheat that is laying towards you, touch the header on the ground and then raise up 8-10 inches and you will get 95% of the crop. when the wheat is laying straight away from you, a 10 degree angle is all you need to achieve 90%. if you cannot get low enough, adjust your skids. if you adjust them all the way, you can dig a hole. just watch out for rocks and badger holes when running on the skids at 3-4 mph! also, the stripper header doesn't like to turn while harvesting, so a straight back and forth approach works a lot better. with 2 machines in the field, you can achieve 41+ acres/ hour with 28' heads and old worn out 9600's or even 8820's. if you run 2- case-IH 8010's with 40' drapers at 5mph you can get 48.5 acres per hour. do i need to do math on cost/acre? another benefit of the stripper head is the residue. the stripper head has replaced our other grain head, heavy harrow, grass herbicide program, and replacing sickle sections. i love that header. in ND i have witnessed the 40" stubble fill to the top with my neighbor's snow, melt in Dec. and refill in Jan. and still be warmer and drier come spring time. soybean yields? Wow. in 06, we received 7" of rain. 5" came in may and up to June 15th. it didn't rain again until September when we got 2 more inches right before harvest. The stripper cut stubble fields produced 20-25 bu more than the tillage neighbors and 8 bu better than soy into corn on corn, 10 bu better than soy into soy. worth its weight in gold. Coup, I had to learn from scratch. Here's what I learned. First raise the hood a little and pull into the field 50 feet. Stop the machine and don't raise the header. Look to see how deep the fingers are into the crop. If they are into the crop enough then set the hood to just be leaning the heads forward. I found the best way is to have the wheat heads about at the top of the head but not so deep that it causes the head to "whiplash" on the hood. Once I have the depth of the fingers set and the hood where it needs to be I just drive by the hood be just over the top of the crop. It doesn't hurt to be too deep but it will just cause more wear and pull harder. Also, I don't think you can drive too fast in thin crops. We ran 9 mph in 20 bu. wheat last year. 6 mph in 60 bu. wheat. Their a lot of fun once you get used to it. I wouldn't want to go back to using a regular grain platform.